HomeMy WebLinkAboutBuilding Miscellaneous 2013-9-10 (2) ILA SPRINGFIELD
,BUILDING • CD
C iL_ID,DEPARTMENT, LLC
Exterior Wall Envelope
l Self-Certification Form
l �jy \ic� U ednRA- (1/4.)5-\-0 fibweS , am the general contractor or the
owner-builder at the following address:
r 2 S LCCA-y 5 Fp � .
Street Address
srC d
City
/ 3 ^ n ) 3Y ` /
Permit#
To conform to the 2011 Oregon Residential Specialty Code (ORSC), Section
R703.1.1, I am notifying the building official that I am aware of the exterior wall
envelope requirements of R703.1.1, and hereby certify that the components of
the exterior wall envelope have been installed in accordance with the code
requirements. [Section R703.1.1 is provided for reference on the reverse side of
this form.]
CY &II • •
•
Signature •
0
Date
•
•
•
•
Shared on's ifs025\dsd'T:\Buildin Forms\2011 Exterior Wall Envelo e.docx Revised 10/1/20'
P g P
Excerpt from 2011 Oregon Residential Specialty Code Section R703, Exterior Covering:
R703.1.1 Exterior Wall Envelope. To promote building durability,"the exterior wall envelope shall
be installed in a manner that water that enters the assembly can drain to the exterior.The envelope
shall consist of an exterior veneer,a water-resistive barrier as required in R703.2,a minimum 1/8
inch space between the water-resistive barrier and the exterior veneer,and integrated flashings as
required in R703.8.The required space shall be formed by the use of any non-corrodible furring
strip,drainage mat or drainage board.The envelope shall provide proper integration of flashings
with the water-resistive barrier,the space provided and the exterior veneer.These components, in
conjunction,shall provide a means of draining water that enters the assembly to the exterior.
Exceptions:
1. A space is not required where the exterior veneer is installed over a water-resistive barrier
complying with section R703.2 which is manufactured in a manner to enhance drainage and
meets the 75%drainage efficiency requirement of ASTM E2273 or other recognized
national standards.
• 2. A space is not required where window sills are equipped with pan flashings which drain to
•
the exterior surface of the veneer in a through wall fashion.All pan flashings shall be
detailed within the construction documents and shall be of either a self-adhering
membrane complying with AAMA 711-07 or of an approved corrosion-resistant material or
a combination thereof.Self-adhering membranes extending to the exterior surface of the
veneer shall be concealed with trims or other measures to protect from sunlight.
3. A space is not required where the exterior veneer is manufactured in a manner to enhance
drainage and meets the 75%drainage efficiency requirements of ASTM E2273 or other
recognized national standards and is installed over a water resistive barrier complying with
section R703.2.
4. A space is not required where the exterior veneer is matching an existing exterior finish as
in additions, alterations,or repairs.
5. A water-resistant exterior wall envelope shall not be required over concrete or masonry
walls designed in accordance with Chapter 6 and flashed according to section R703.7 or
•
R703.8.
6. Compliance with the requirements for a means of drainage, and the requirements of .
Section R703.2 and Section R703.8,shall not be required for an exterior wall envelope that
has been demonstrated to resist wind-driven rain through testing of the exterior wall
envelope, including joints, penetrations and intersections with dissimilar materials, in
accordance with ASTM E 331 under the following conditions:
6.1. Exterior wall envelope test assemblies shall include at least one opening,one control
joint, one wall/eave.interface and one wall sill.All tested openings and penetrations
shall be representative of the intended end-use configuration.
6.2. Exterior wall envelope test assemblies shall be at least 4 feet by 8 feet in size.
6.3. Exterior wall assemblies shall be tested at a minimum differential pressure of 6.24
pounds per square foot. •
- 6.4. Exterior wall envelope assemblies shall be subjected to a minimum test exposure
•
duration of 2 hours.
The exterior wall envelope design shall be considered to resist wind-driven rain where the
results of the testing indicate that water did not penetrate:control joints in the exterior
wall envelope;joints at the perimeter of openings penetration;or intersections of
terminations with dissimilar materials.
•